技術文章

聯系我們CONTACT

湖北德普電氣股份有限公司

地 址:襄阳市高新区(自贸区)叶店路16号
电 话:0710-3276513传 真:0710-3276513
邮 箱:xfdpxs@126.com
网 址:www.techpow.com.cn
全国统一服务热线:400 0710 600



武漢德普新源科技有限公司

地址:武漢東湖高新技術産業開發區華師園北路6號
電話:027-81610218
傳真:027-81610218



湖北德普智能裝備有限公司

地址:湖北省襄陽市高新區(自貿區)葉店路16號
電話:0710-3357890

您當前的位置:主頁 > 技術文章 > 技術文章

充電電池基本測試

上傳時間:2017-04-18閱讀次數:編輯:admin
Contents:
-EN61951-1:2003
Secondary cells and batteries containing alkaline or other non-acid electrolytes-Portable
sealed rechargeable single cells
Part1:Nickel-Cadmium
含堿性或其他非酸性電解質的二次電池和蓄電池.便攜密封可再充電單電池
第1部分_鎳镉電池.
-EN61960:2004
Secondary cells and batteries containing alkaline or other non-acid electrolytes-
Secondary lithium cells and batteries for portable applications
裝有堿性或其它非酸性電解液的蓄電池和電池組用于便攜式的充電锂電池和電池組
-ANSI C18.2M
PART1: American national standard for portable rechargeable cells and
batteries-General specifications
第一部分:便攜式充電電池的美國標准-一般要求
-Battery Dimension
電池尺寸
EN61951-1:2003
Secondary cells and batteries containing alkaline or other non-acid
electrolytes-Portable sealed rechargeable single cells
Part1:Nickel-Cadmium
含堿性或其他非酸性電解質的二次電池和蓄電池.便攜密封可再充電單電
第1部分_鎳镉電池.
5.3 Marking
標識
7.1 Charging procedure for test purposes
充電的測試流程
7.2.1 Discharge performance at 20℃
20℃環境溫度下的放電性能
Marking
標識
Each jacketed cell supplied without connections shall carry durable markings giving the
following minimum information:
每个单独电池要提供至少包括以下信息的耐久標識:
-Sealed, rechargeable nickel-cadmium or Ni-Cd
密封的,可充電的鎳镉
-Cell designation
電池類型
-Rated capacity
額定容量
-Nominal voltage
標稱電壓
-Recommended charge rate and time or permanent charge current for “T” cells
對于T電池(預計在達到40℃高溫下永久充電的電池),建議的充電速度和時間或永久充電電
-Polarity
極性
-Date of manufacture (which may be in code)
生産日期(可以使用代碼)
-Name or identification of manufacture or supplier
制造商或供應商的名稱或身份識別
 7.1Charging procedure for test purposes
充電測試流程
Unless otherwise stated in this standard, the charging procedure for test
purposes shall be carried out in an ambient temperature of 20℃±5℃ at a
constant current of 0.1ItA for 16h(It A=CnAh/1h)
除非本标准特殊说明,充电程序是在20℃± 5℃环境温度和0.1ItA的恒电流下充
電16h.
Prior to charging, the cell shall have been discharged in an ambient
temperature of 20℃±5℃, at a constant current of 0.2ItA down to a final
voltage of 1.0V
充電前,電池在20℃±5℃環境溫度下且在0.2ItA的恒電流下已放電到終止電壓爲
1.0V
 7.2.1 Discharge performance at 20℃
20℃環境溫度下放電性能
The cell shall be charged in accordance with 7.1.After charging, the cell shall be
stored, in an ambient temperature of 20℃±5℃,for not less than 1h and not
more than 4h
電池按照7.1條款充電,充電後,要將電池在20℃±5℃環境溫度下存放1~4h
The cell shall be discharged at 0.2It A rate in an ambient temperature of
20℃±5℃ to a final voltage of 1.0V, if the test is based on the rated capacity
C5Ah(5 is the time base in hours for which the capacity is declared), the
minimum discharge duration shall be 5h
電池在20℃±5℃環境溫度下且在0.2ItA的恒電流下放電到終止電壓爲1.0V
,如果测试是根据額定容量C5Ah(5表示宣称容量的放电时间基数以小时表示)来进
行的,放電時間不能小于5h.
Secondary cells and batteries containing alkaline or other non-acid
electrolytes-Secondary lithium cells and batteries for portable applications
裝有堿性或其它非酸性電解液的蓄電池和電池組用于便攜式的充電锂電池
和電池組
5.3 Marking
標識
7.1 Charging procedure for test purposes
充電的測試流程
7.2.1Discharge performance at 20℃(rated capacity)
20℃環境溫度下的放電性能(額定容量)
 Marking
標識
Each cell or battery shall carry clear and durable markings giving the following information:
每个电池应按照如下信息提供清晰,耐久的標識:
-Rechargeable Li or Li-ion;
可替換的锂或锂離子
-Battery or cell designation (e.g.ICR19/66)
電池類型
-Polarity
極性
-Date of manufacture (which may be in code)
生産日期(可以用代碼表示)
-Name or identification of manufacture or supplier
制造商或供應商的名稱或身份識別
Battery markings shall provide the following additional information:
电池標識要提供如下额外信息:
-Rated capacity
額定容量
-Nominal voltage
標稱電壓
7.1 Charging procedure for test purposes
充電測試流程
Prior to charging, the cell shall be discharged at 20℃±5℃, at a constant
current of 0.2It A down to a specified end -of -discharge voltage.
充電前,電池要在20℃±5℃環境溫度和在0.2ItA的恒電流下放電到終止電壓爲
1.0V
Cells or batteries shall be charged, in an ambient temperature of 20℃±5℃,
using the method declared by the manufacture.
電池在20℃±5℃的環境溫度下使用制造商宣稱的方法充電
7.2.1 Discharge performance at 20℃(rated capacity)
20℃環境溫度下的放電性能(額定容量)
Step1-The cell or battery shall be charged in accordance with 7.1
步驟1-電池根據7.1條款充電
Step2-The cell or battery shall be stored , in an ambient temperature of20℃±5℃ ,
for not less than 1h and not more than 4h
步骤2-电池在20 ℃±5℃ 的环境温度下存放,时间在1h~4h
Step3-The cell or battery shall be discharged, in an ambient temperature of 20
℃±5℃ , at a constant current of 0.2It A, until its voltage is equal to the
specified end-of-discharge voltage.
步骤3-电池在20 ℃±5℃ 的环境温度下且在0.2It A的恒电流下放电直到电压达到特
指的終止電壓
Step 4-The capacity (Ah) delivered during step 3shall be not less than 100%of the
rated capacity declared by the manufacture. Steps 1 to 4 may be repeated
up to four additional times, as necessary to satisfy this requirement.
步骤4-在步骤3中得到的容量不能小于制造商宣称的100%的額定容量。为了满足本要求,
1到4步驟可以再重複進行四次
C18.2M PART1: American national standard for portable
rechargeable cells and batteries-General specifications
ANSI C18.2M 第一部分:便攜式充電電池的美國標准-一般要求
method: Charge for 20h at 0.1C-rate. Let rest 1h.
充電方法:電池在0.1C下充電20h,停放1h
Rated Capacity and service life: Discharge at 0.2C-rate until terminal
voltage=cut off voltage (EODV) of 1.0V/cell.Calculate and report capacity. Shall
meet or exceed claimed capacity.
額定容量和使用寿命:在0.2C下放电直到终止电压为1.0V,计算容量,实际容量
應滿足或超過宣稱容量值
Dimension電池尺寸 :
1. Cylindrical cells dimensionally interchangeable with primary battery
在尺寸上與原電池可互換的圓柱形電池(Ni-Cd)
Standard: in accordance with IEC60086-2
標准:根據IEC60086-2
Designation: R03(alson known as AAA), R6(alson known as AA)
类型:R03(在某些国家也称作AAA), R6(在某些国家也称作AA)
Dimensional drawings as figure 1&2
尺寸圖表示如圖1&2
Specifications as table1
尺寸要求如表1
Table 1
Note:
A-maximum overall height of the battery
電池整體的最大高度
C-minimum outer diameter of the negative flat contact surface
陰極平面的最小外徑
F-maximum diameter of the positive contact within the specified projection height
陽極接觸的最大直徑
G-minimum projection of the flat positive contact
陽極接觸的最小突出高度
Φ-maximum and minimum diameters of the battery
電池的最大和最小直徑
2. Cells not dimensionally interchangeable with primary batteries
與原電池不能在尺寸上互換的電池(Ni-Cd)
Standard: in accordance with EN61951-1:2003
Dimension is as the following table 2
Table 2
3. Standard secondary lithium cell dimension:
标准的可充电的锂電池尺寸(listed in Table 3)
Standard: in accordance with EN61960-1:2004
Table 3
關于我們 産品中心 研發中心 德普智能 新聞中心 産品應用 聯系我們 技術文章

公司地址:襄阳市高新区(自贸区)叶店路16号 服务电话:400 0710 600
Copyright © 2015-2018 湖北德普電氣股份有限公司 版权所有

X請用手機掃描微信二維碼